3
SERVICE INFORMATION
PPF-2100 PPT-2100
PPT-2400 PPFD-2400
Models PPT-2100 PPT-2400 PPFD-2400
Dimensions Length(collapsed) mm(in) 2260 (89.0) 2734 (107.6) 2320 (91.3)
Length(fully extended) mm(in) 3410 (134.3) 3884 (152.9) N/A
Length(with extension)* mm(in) 5000 (196.9) 5468 (215.3) 3910 (153.9)
Width mm(in) 230 (9.06) 230 (9.06) 220 (8.66)
Height mm(in) 221 (8.70) 221 (8.70) 230 (9.06)
Dry weight kg(lb) 7.27 (16.0) 7.85 (17.3) 6.95 (15.3)
Engine Type KIORITZ, air-cooled, two-stroke, single cylinder
Rotation Counterclockwise as viewed from the output end
Displacement cm
3
(in
3
) 21.2 (1.294) 23.6 (1.440)
Bore mm(in) 32.2 (1.268) 34.0 (1.339)
Stroke mm(in) 26.0 (1.024) 26.0 (1.024)
Compression ratio 6.5 6.3
Carburetor Type Diaphragm, horizontal-draught, with primer (purge pump)
Model ZAMA C1U-K52 WALBRO WT424B
Ignition Type CDI (Capacitor discharge ignition) system
in a single integrated piece w/ESG
Spark plug BPMR7A, RCJ-7Y, BPM7A, CJ-7Y
Starter Type Automatic rewind
Rope diameter x length mm(in) 3.0 x 1000 (0.12 x 39.4)
Fuel Type Premixed two-stroke fuel (Refer to Operator's manual.)
Tank capacity cm
3
(U.S.fl.oz.) 420 (14.2)
Clutch Type Centrifugal, 2-shoe slide
Drive shaft Type Aluminum extrusion Fiberglass
Upper OD mm(in) 15.1 (0.59) 15.8 (0.62)
Length mm(in) 1588 (62.5) 2026 (79.8) 1760 (69.3)
Lower Length mm(in) 1543 (60.75) N/A
Housing Type Upper / Lower Aluminum / Fiberglass
Upper OD - ID mm(in) 34.6 - 32.1 (1.36 - 1.26)
Length mm(in) 1594 (62.8) 2032 (80.0) 356 (14.0)
Lower OD - ID mm(in) 46.5 - 38.9 (1.83 - 1.53)
Length mm(in) 1524 (60.0) 1491 (58.7)
Gear case Reduction ratio 1.5
Gear tooth Spiral bevel, Spur
Lubrication Lithium based grease
Guide bar / Saw chain lubrication type Automatic
Tank capacity, oil cm
3
(U.S.fl.oz.) 225 (7.6)
Sprocket Type Spur
Number of teeth 6
Pitch in 3/8
Guide bar Type Sprocket nose
Called length in 10 12
Gauge in 0.043 (0.050 for Type 1E and Canada)
Saw chain Number of drive links 39 44
pitch in 3/8
Gauge in 0.043 (0.050 for Type 1E and Canada)
*Extension is an option. OD: Outer Dia., ID: Inner Dia.
Comentários a estes Manuais